Agarose Electrophoresis

Agarose Electrophoresis

Agarose elctrophoresis is performed to visualize your PCR products. This step allows
you to determine whether your PCR was successful, whether the resulting product is the correct size, whether other products were amplified as well, and whether the
concentration of the resulting product is suitable for cycle sequencing. All gel work
should be performed in the HIGH DNA area.

Precautions
1. Always wear gloves! This is essential to limit the spread of PCR products around
the lab as well as protecting against exposure to Ethidium Bromide.
2. Treat Ethidium Bromide with respect (it is a powerful mutagen) and ensure that it
does not get spread around the lab.
3. Wash hands when finished.

Materials Equipment
1. Agarose 1. Balance
2. 0.5X TBE 2. Erlenmeyer flask
3. weighing paper 3. Microwave
4. Gel box with comb

Step 1: Mixing Gel
1. On the scale, weigh 1 gram of agarose onto a piece of weighing paper.
2. Add agarose to Erlenmeyer flask.
3. Add 100mL of 0.5X TBE to Erlenmeyer flask.
4. Swirl vigorously to thoroughly mix agarose.
Slurry will by opaque.

Step 2: Melting Gel
1. Put agarose and 0.5x TBE slurry into microwave.
2. Heat on HIGH for 30 seconds at a time.
3. After 30 seconds, remove from microwave and swirl. Becareful as the mixtue will be HOT.
4. After 1 minute of heating, repeat heating and swirling procedure every 10 seconds until mixture is clear.
5. If the mixture begins to boil, stop and IMMEDIATELY remove the agarose. Swirl until
mixture is clear.


Step 3: Pouring the Gel
1. Before pouring, gel must be cool enough for you to hold the Erlenmeyer flask in your hand. Pouring boiling hot gel will warp the gel boxes.
2. Place gel tray into casting chamber.
3. Add casting comb(s) into the appropriate slot(s).
4. Pour agarose into gel tray to about 5-7mm.
5. Let sit for at least 30 min, until gel is cool to touch and is opaque in appearance.
6. Once set, place gel and tray into gel rig, with wells on the left (cathode) side. Then, fill gel rig with 0.5X TBE sufficient to cover the entire gel.
7. Carefully remove combs by pulling them upwardsfirmly and smoothly in a continuous motion. The remaining depressions are the wells into which your samples will be loaded.

Step 4: Loading the Gel
1. Cut a piece of parafilm and place it flat on the bench top. You may have to rub or scratch it to stick it down.
2. Using a pipette, place small dots of 6X loading dye (about 1-2uL) onto parafilm, in rows of 8, 1 dot for each PCR sample that will loaded on the gel. It is not necessary to be exact, and it is not necessary to change the tip.
3. Using a pipette take 3 μl of product and pipette it onto its corresponding dye dot, then mix the sample and dye by pipetting up and down. Then, pipette up the dye/sample solution and pipette it into the proper well.
4. After loading the first sample into the well, wash out your pipette tip by pipetting up and down several times in the buffer, then blot tip dry with a Kimwipe. In this way, all of your samples may be loaded using ONE tip.
5. Once all samples have been loaded into the gel, using a fresh tip, pipette 3uL of
the DNA ladder into well number 1 of each row of wells.
6. Put gel box cover into place (this step is essential for your gel to run and to minimize the risk of electric shock). Turn on power supply. Run the gel for 75
minutes at 80 volts.
7. Check for bubbles at the cathode side to ensure that gel rig is running. Clean up, deglove, and wash hands.


Step 5: Visualizing the Gel
1. Turn off power supply. Using gloved hands, remove the cover from the gel box.
2. Remove the gel and casting tray from rig, avoiding dripping buffer all over the
benchtop.
3. Carefully slide the gel off of the casting tray and into ethidium bromide solution.
Caution: ethidium bromide is a mutagen and should be treated with respect. If you
get ethidium bromide on you gloves, immediately change your gloves, placing the
contaminated gloves into the ethidium bromide trash. Do not spread ethidium
bromide around the lab.
4. Soad the gel in the ethidium bromide solution for 10-15 minutes to stain. Using a
spatula, remove the gel from ethidium bromide and rinse for 30 seconds in a tray
0.5x buffer. The gel may be left in the 0.5X buffer for longer to “destain” the gel
and improve contrast of stain, but this step is often unnecessary.
5. Using the spatula, carefully remove the gel from the destaining buffer and place
the gel on UV light box, avoiding creating bubbles underneath the gel.
6. Put on UV protecting face shield and turn on UV light box to see stained sample
bands and DNA ladder. Ensure that all around you are protected for UV exposure.
7. If bands are strong, take a picture using the Polaroid camera (below). If bands are
weak, return gel to ethidium bromide stain bath as the gel has been insufficiently
stained.
Step 6: Taking a picture. Remember that the gel has been soaking in Ethidium
Bromide. All objects and surfaces that the gel comes into contact with will be
contaminated with Ethidium Bromide. Always wear gloves and limit the spread of
Ethidium Bromide to protect yourself and your lab mates.
1. Ensure that you are still wearing your gloves and UV face shield.
2. With the gel flat on the UV light box, position the hood of Polaroid camera over
the gel so that the hood is centered over the gel.
3. Turn on the UV light box.
4. Keeping the camera steady, pull the trigger and HOLD the trigger until there is
silence (i.e. the shutter has opened and closed. This may take 0.5-2.0 seconds
depending on the cameras exposure settings).
5. Turn off the UV light box.
6. Pull WHITE film tab on camera to remove film. Wait 1 minute
7. After one minute has passed, pull backing off of film to check whether the gel
imaged properly.
8. Once picture is developed and you have a good picture of your gel, remove your
gel and put in gel disposal box.
9. Wipe down the UV light box with Kimwipes and dispose of in gel disposal box.
Remember that all of these surfaces and wipes are contaminated with Ethidium
Bromide.
10. Remove your gloves and dispose of in the Ethidium Bromide trash.
11. Wash hands thoroughly.
12. Label your picture.